Please wait, content is loading

SmartAPEX Journal · Climate

Smart thermostat for a split AC: how infrared control works

Split air conditioners come with a handheld infrared remote, one per room, which goes missing and runs out of batteries. A wall thermostat that speaks the air conditioner’s infrared language puts the AC on the wall and into the smart home, without opening the air conditioner.

5 min read

How an air conditioner remote works

Press a button on a split AC remote and it flashes an invisible infrared code at the indoor unit. With most split air conditioners, each code carries the whole setting at once: the mode, the temperature and the fan speed. That is why the remote’s own screen keeps track of what is set. Infrared is one-way: the air conditioner does not answer, and the light needs a clear path to the indoor unit.

24°SmartAPEX thermostat -IR24°Split AC indoor unitCool24 °CFan highEach command carries the whole setting, as the AC’s own remote does.
One infrared command carries mode, temperature and fan speed together, and the air conditioner applies all three.

Three ways to bring a split AC into a smart home

InfraredAir conditionerNo wiring into the ACWired gatewayAir conditionerTwo-way, with statusAC maker’s appAir conditionerSeparate app, onlineThermostatMini IPstatusInternet
Infrared from the wall, a wired gateway that also reports status, or the air conditioner maker’s own app through the internet.
IR thermostat Wired gateway (Modbus) AC maker’s app
Wiring into the AC None An interface on the AC, or a VRF gateway None, or a Wi-Fi module
Direction One-way: commands Two-way: commands and status Two-way
Needs the internet No No Usually, through the maker’s cloud
Part of the house system Yes, on the wall and in scenes Yes A separate app
Best for Split units in homes VRF and larger systems A single unit with no smart-home system

The SmartAPEX CAN thermostat -IR

In the wired SmartAPEX range, the CAN thermostat -IR (APX-TCA-IR) is the air conditioner’s wall control. It uses its built-in IR emitter, or an IR probe on its G/I terminals in place of a temperature probe (never both), and sends the air conditioner’s own infrared commands. There is no interface module to fit inside the AC.

It offers Heat, Cool, Fan, Dry and Auto, as far as the air conditioner’s code supports them, fan speeds Low, Medium, High and Auto, and a set temperature in 1 °C steps within the AC’s limits. The air conditioner keeps the room at that temperature with its own regulation, and the display shows the room temperature from the thermostat’s own sensor. Its four relay outputs become ordinary switch outputs.

Setting it up: load the air conditioner’s code set

Air conditioner makers use different infrared codes. The installer opens the CAN devices page of the SmartAPEX gateway in a browser, picks the air conditioner’s brand and code set, and loads it; it reaches the thermostat over the CAN bus. Until a code set is loaded the display shows IrE and the keys wait.

Gateway · CAN devicesThermostat -IR · BedroomAC brandYour AC’s brandCode setCode set 3LoadCANIrE24°Thermostat -IR
Pick the brand and code set, load it over CAN, and the thermostat is ready.

In a Z-Wave home: ThermoIR

In a Z-Wave home, the ThermoIR thermostat (TZCA · TZCD) does the same job together with a Z-Wave infrared transmitter placed in view of the air conditioner: the Z-Wave controller passes the mode, temperature and fan speed on to the transmitter. ThermoIR also switches four light circuits. See the whole family in Z-Wave thermostat and light switch in one.

Tips for a good installation

One thermostat per indoor unit

Plan one thermostat for each air conditioner, in the room it cools.

Keep a clear line of sight

Infrared does not pass through walls or furniture. The emitter or probe must face the indoor unit’s receiver.

Test every mode at hand-over

After loading the code set, try each mode and fan speed once with the air conditioner running.

VRF and central systems

Connect them over Modbus: the Mini IP gateway maps a Modbus HVAC unit or VRF gateway and links it to a SmartAPEX CAN thermostat, with status coming back.

Frequently asked questions

Do I have to open or rewire the air conditioner?

No. An IR thermostat sends the same infrared commands as the air conditioner’s own remote, so no interface module goes inside the AC.

Which modes does the SmartAPEX IR thermostat support?

Heat, Cool, Fan, Dry and Auto, as far as the air conditioner’s code supports them, with fan speeds Low, Medium, High and Auto.

Can the thermostat tell whether the AC is really on?

No. Infrared is one-way, so the thermostat shows what it last sent. For status back from the air conditioner, connect it over Modbus through the SmartAPEX Mini IP gateway.

Does it need the internet?

No. The infrared commands and the CAN bus work inside the house, without the internet.

Will it work with my air conditioner?

It is made for split and ducted air conditioners controlled by an infrared remote. The installer loads your AC’s brand and code set and tests every mode at hand-over.

Planning a smart home? The SmartAPEX Home Planner suggests keypads, thermostats and modules room by room, and sends your plan to us.

Open the Home Planner

Product details from the SmartAPEX CAN thermostat, Z-Wave thermostat and Mini IP gateway product pages and firmware.