Please wait, content is loading

SmartAPEX Journal · Set-up

Program a smart home without ETS: the APEX Bindings map

In a wired smart home, someone has to tell each button what it controls. With many systems that takes special software, a licence and a specialist. With SmartAPEX it takes a web browser. This is how the Bindings map works.

4 min read

Link a keypad to a light: click, click, done

The Bindings map shows every wall keypad, thermostat and input on the left, and every relay channel, DALI address and thermostat on the right. Draw a line from one to the other and the binding is made.

192.168.1.20 · BindingsWHEN · SOURCESTHEN · TARGETSKeypad · Living roomButton 1Button 2Button 3Button 4Thermostat · BedroomKey 1IP Relay 24CHCh 02 · HallCh 03 · Ceiling lightCh 05 · CurtainDALIGroup 1 · Dining✓ Saved on the keypad
Pick Button 1 on the living-room keypad, pick Channel 3, and the line is saved on the keypad. Press the button on the wall and the ceiling light answers.

Click the button or input

Any keypad button, thermostat key or input of the 16-channel digital input module.

Click what it should control

A relay channel for lights, curtains or a fan-coil, a DALI address, group or scene, or a thermostat’s power and mode.

Press it on the wall

The binding is already live. There is nothing to download or compile.

Short press, long press, double and triple click

Each touch position on a SmartAPEX CAN keypad can do different things for a short press, a long press, a double click and a triple click. Bound to a DALI light, one button works as a full dimmer: tap to switch, hold to dim. A thermostat key can switch a relay, and a keypad can set a thermostat’s power and mode.

Short pressCeiling light on / offLong pressDim the lightDouble clickOpen the curtainsTriple clickEverything offExample actions
One touch position, four press types, four different actions. The actions here are examples.

Where the links live

Bindings are stored on each source device, so a link does not depend on the page, or the computer, that made it. If a device is offline while you make a change, the module keeps the change and sends it the moment the device answers on the bus again. The Mini IP gateway can find, set up, bind and update up to 64 SmartAPEX keypads, thermostats and inputs.

Mini IP · CAN devices · UpdateKeypad · Living room✓ UpdatedKeypad · Kitchen✓ UpdatedThermostat · Bedroom✓ UpdatedThermostat · Majlis✓ UpdatedDigital input 16ch✓ Updated
From the Mini IP gateway’s web page, several devices on the bus are updated together.

Bindings map vs KNX programming with ETS

KNX also links devices directly, through “group addresses”, and it does so across hundreds of brands. The difference is in what it takes to make and change those links.

KNXSmartAPEXETSlicenceKNXinterfaceDeviceaddressesGroupaddressesLinkobjectsDownloadto devicesClickthe buttonClickthe lightDone✓No licence, no dongle,no project file.
Linking a keypad to a light: the usual KNX steps, and the SmartAPEX Bindings map.
SmartAPEX Bindings map KNX
Software None to install: the page is built into the module and opens in a browser ETS engineering software on a Windows computer
Licence None An ETS licence, held on a USB licence key or in the cloud; the cloud licence needs a permanent internet connection
Connection to the bus The home network; the module is already on the bus A KNX interface (USB or IP) between the computer and the bus
Making a link Click the source, click the target Give each device an address, usually by pressing its programming button, create group addresses, link them to device objects, then download to each device
Where the set-up is kept On the devices, read back by the page On the devices and in the ETS project file, which is needed for later changes
Who can do it A SmartAPEX installer with a browser A KNX-trained integrator
Brands SmartAPEX devices Any KNX device from any manufacturer

Why it matters to a home owner

A smart home changes over the years: a room becomes an office, a light moves, a button should open the curtains instead. With the Bindings map, such a change is a few minutes in a browser on site. Read more about the wired system behind it in CAN bus vs KNX: how a wired smart home works.

Frequently asked questions

Do I need ETS to program SmartAPEX?

No. ETS is the engineering tool for KNX. SmartAPEX devices are linked on the Bindings map in the web page of the relay module, the DALI gateway or the Mini IP gateway, in an ordinary browser.

Do I need a software licence or a dongle?

No. The Bindings map needs no software licence, no dongle and no project file. The links are stored in the devices and read back by the page.

What can a keypad button control?

Relay channels for lights, curtains and fan-coils, DALI addresses, groups and scenes, and a thermostat’s power and mode. A short press, long press, double click and triple click can each do something different.

What if a device is offline when I change a binding?

The module keeps the change and sends it the moment the device answers on the bus again.

Planning a smart home? The SmartAPEX Home Planner suggests keypads, thermostats and modules room by room, and sends your plan to us.

Open the Home Planner

KNX details from the KNX Association’s published ETS licensing information. SmartAPEX details from the relay module, DALI gateway and Mini IP gateway product pages.