Please wait, content is loading

SmartAPEX Journal · Climate

Z-Wave thermostat and light switch in one: five models, one panel

Most rooms need two things on the wall: a thermostat and a few light switches. The SmartAPEX Z-Wave thermostat can be both. It comes in five models that share one faceplate and one back-unit, and each model gives its four outputs a different job.

5 min read

Why put climate and lights on one wall panel?

Beside the door of a bedroom or a majlis there is often a thermostat with two or three light switches next to it. Each needs its own wall box, its own wiring and its own entry in the app. A panel that does both keeps the wall clean. Across a whole project it also means one design, one spare part and one installer routine.

22°Same faceplate, same back-unitFan-coil thermostatTZA · TZDQ1Fan lowQ2Fan mediumQ3Fan highQ4Valve0-10 V thermostatTZ010Q1Fan lowQ2Fan mediumQ3Fan high0-10 VModulating valveThermoLightTZLA · TZLDQ1Light 1Q2Light 2Q3FanQ4ValveThermoIRTZCA · TZCDQ1Light 1Q2Light 2Q3Light 3Q4Light 4FloorHeatTZFA · TZFDQ1Light 1Q2Light 2Q3Light 3Q4Floor heating
The same panel as five models. The firmware model decides what the four outputs, Q1 to Q4, do.

The five SmartAPEX Z-Wave thermostat models

Model Climate Lights Outputs
Fan-coil thermostat
TZA · TZD
A 3-speed fan and a valve, or two fan speeds with separate heating and cooling valves for 4-pipe fan-coils None Q1–Q3 fan, Q4 valve
0-10 V thermostat
TZ010
Three fan speeds and a 0-10 V output for a modulating valve None Q1–Q3 fan, 0-10 V valve
ThermoLight
TZLA · TZLD
A fan-coil with fan and valve, or a 2-speed fan 2 Q1, Q2 lights; Q3 fan; Q4 valve
ThermoIR
TZCA · TZCD
A split or ducted air conditioner over infrared: Heat, Cool, Fan, Auto, Dry 4 Q1–Q4 lights
FloorHeat
TZFA · TZFD
Water or electric floor heating, with a flame icon while it heats 3 Q1–Q3 lights, Q4 floor

On the mains back-unit, Q1 to Q4 are switched live outputs; on the 12–24 V back-unit they are volt-free contacts. Follow the manual for the loads each output can switch.

2-pipe or 4-pipe fan-coil?

A fan-coil blows room air across a coil of water pipes. In a 2-pipe system the same coil carries hot water in winter and chilled water in summer, so one valve is enough. A 4-pipe system has separate heating and cooling coils, so a room can heat or cool at any time of year. The fan-coil model handles both: three fan speeds and one valve, or two fan speeds with separate heating and cooling valves, chosen by one setting.

2-pipe fan-coil4-pipe fan-coilone coilvalveHot or cold water, by season.heating coilcooling coilHeating and cooling at any time.
A 2-pipe fan-coil has one coil and one valve. A 4-pipe fan-coil has a heating coil and a cooling coil, each with its own valve.

How the fan speed follows the room

The thermostat compares the room temperature with the set point. While the gap is large the fan runs fast; as the room gets closer, the fan steps down; when the set point is reached it stops, or keeps running on low if the installer prefers. The temperature difference at which it steps (Delta-T) is adjustable, and heat only, cool only, or heat and cool is a setting too.

set pointRoomFanHighMediumLowOffIllustration. The step points follow an adjustable temperature difference (Delta-T).
As the room approaches the set point, the fan steps from high to medium to low, then stops.

On/off valve or 0-10 V valve?

Most fan-coil valves are either open or closed. A modulating valve can also open part-way. The 0-10 V model sends a signal between 0 and 10 volts that opens the valve in proportion to the demand, for smoother and quieter regulation. The same output also suits building-management inputs.

On/off valveopenclosed0-10 V valveopenclosed
An on/off valve swings between fully open and closed. A 0-10 V valve settles part-way, at the opening the room needs.

Floor heating with three lights

FloorHeat switches a water or electric floor-heating zone on its fourth output and shows a flame on the display while the floor is heating. Its other three outputs are light circuits on the thermostat’s own keys, a good fit for bathrooms and bedrooms with underfloor heating.

Air conditioners over infrared

ThermoIR keeps four light circuits on its outputs and controls a split or ducted air conditioner over infrared: Heat, Cool, Fan, Auto and Dry. In a Z-Wave home it does this together with a Z-Wave infrared transmitter placed in view of the air conditioner. For wired homes, the SmartAPEX CAN thermostat -IR sends the air conditioner’s commands itself. Read more in Smart thermostat for a split AC: how infrared control works.

One device on the wall, separate devices in the app

Each model joins the Z-Wave network as one device, and the controller shows its parts separately: the lights as switches and the climate part as a thermostat, so scenes and schedules can use each of them. All five run on Z-Wave 800 Long Range and are updated over the air. They offer 15 LED colours per key and state, separate display and button brightness, and a calm standby level. Like every SmartAPEX Z-Wave device they are always powered, so they also strengthen the mesh; see Z-Wave vs Zigbee.

Which model for which room?

Fan-coil, no lights nearby

The fan-coil thermostat, 2-pipe or 4-pipe.

Modulating valves or a BMS

The 0-10 V thermostat.

Fan-coil and two light circuits

ThermoLight, for bedrooms, offices and majlis rooms.

Split AC and up to four lights

ThermoIR.

Underfloor heating and three lights

FloorHeat.

Same look everywhere

All five use the Crystal glass and Classic metal faceplates of the SmartAPEX keypads.

Frequently asked questions

Can a Z-Wave thermostat also switch lights?

Yes. ThermoLight switches two light circuits, FloorHeat three and ThermoIR four, all on the thermostat’s own keys and outputs.

Does it work with 4-pipe fan-coils?

Yes. The fan-coil model can run two fan speeds with separate heating and cooling valves, chosen by one setting, or three fan speeds and one valve for 2-pipe systems.

What does a 0-10 V thermostat do?

It sends a signal between 0 and 10 volts that opens a modulating valve in proportion to the demand, instead of only fully open or closed.

Can it control a split air conditioner?

Yes. ThermoIR controls a split or ducted air conditioner over infrared together with a Z-Wave infrared transmitter. In wired homes, the SmartAPEX CAN thermostat -IR sends the infrared commands itself.

Which Z-Wave controller does it need?

Any compatible Z-Wave controller, including the SmartAPEX Home Center wall panel, which has ready-made settings for SmartAPEX Z-Wave keypads and thermostats.

Planning a smart home? The SmartAPEX Home Planner suggests keypads, thermostats and modules room by room, and sends your plan to us.

Open the Home Planner

Product details from the SmartAPEX Z-Wave thermostat product page and firmware. Z-Wave 800 Long Range is part of the Z-Wave standard (Z-Wave Alliance).